Coolant Filtration System for Cast Iron Machining

Cast Iron is used for most major engine components and motion transmission. Various operations like drilling tapping and turning on such components generate large quantum of chips. Individual filtration system is prone to breakdowns and do not give required filtration levels resulting in low coolant life.

In a CFS, Dirty fluid along with chips is collected in the dirty tank. This tank has a continuously moving scarper conveyor which removes the chips that settle down. The coolant then passes through drum type magnetic separator’s mounted on the side walls of the scraper conveyors. This ensures that the complete flow passes through a dense magnetic grid. The filtered fluid drops into a clean tank. Clean fluid pump supply pressurized fluid to the machines. Sizing of the tanks, magnetic drums and pumps is done based on your total flow requirement. In addition, fine filter housing can be provided for through spindle coolant.

Features & Benifits

  • Large dirty tank gives enough time for the chips to settle. It also improves heat dissipation and single point chip collection.
  • Independently rotating magnetic drums with finned pole plates increase the magnetic density.
  • Multiple drums for larger systems. Drums can be isolated individually.
  • Our unique pole plate design and scraper arrangement improves magnetic separation efficiency and ease of maintenance.
  • Independently rotating magnetic drums with finned pole plates increase the magnetic density.
  • Multiple drums and drums can be isolated individually.
  • Our unique pole plate design and scraper arrangement improves magnetic separation efficiency and ease of maintenance.
  • Built in PLC Controlled electrical and mechanical safety with Auto conveyor Jamming logic.
  • Skimmers, Weekend agitation, VFD can be added with further enhance the system.
  • Customized design to suit your specific requirement.

Coolant Filtration System for Steel Machining

  • Steel because of its ductile and tensile strength is widely used in auto component industry. ­­But steel machining generally generates long curly chips. These chips are difficult to handle and do not flow with the help of pressurized coolant flow. Due to this restriction making a CFS was always a challenge.

    Veeraja has now developed a unique chip cutter which can be attached to the outlet of individual chip conveyor of each machine. This chip cutter shreds the steel chips into smaller manageable size. These can now be conveyed using traditional methods of gradient gravity flow.

    In a CFS, Dirty fluid along with chips is collected in the dirty tank. This tank has a continuously moving scarper conveyor which removes the chips that settle down. The coolant then passes through drum type magnetic separator’s mounted on the side walls of the scraper conveyors. This ensures that the complete flow passes through a dense magnetic grid. The filtered fluid drops into a clean tank. Clean fluid pump supply pressurized fluid to the machines. Sizing of the tanks, magnetic drums and pumps is done based on your total flow requirement. In addition, fine filter housing can be provided for through spindle coolant.

Features & Benifits

    • Multi cutter chip cutter for built mechanical and electrical safety.
    • individual cutter can be assembled in reverse way to expose second cutting edge. individual cutter can be replaced.
    • Independently rotating mesh drum with inward and outward flushing nozzle.
    • Large dirty tank gives enough time for the chips to settle. It also improves heat dissipation. Single point chip collection.
    • Independently rotating magnetic drums with finned pole plates increase the magnetic density.
    • Multiple drums and drums can be isolated individually.
    • Our unique pole plate design and scraper arrangement improves magnetic separation efficiency and ease of maintenance.
    • Built in PLC Controlled electrical and mechanical safety with Auto conveyor Jamming logic.
    • Skimmers, Weekend agitation, VFD can be added with further enhance the system.

Coolant Filtration System for Aluminium Machining

Aluminium is vastly used in automobile components. Various operations like drilling tapping on such components generate large quantum of chips. Individual filtration system is prone to breakdowns and do not give required filtration levels resulting in low coolant life.

In a CFS, Dirty fluid along with chips is collected in the dirty tank. This tank has a continuously moving scarper conveyor which removes the chips that settle down. A rotating mesh drum is placed inside this tank. The fluid passes through the mesh drum while the chips are separated on the outside. The filtered fluid drops into a clean tank. Clean fluid pump supply pressurized fluid to the machines. Sizing of the tanks, mesh drum and pumps is done based on your total flow requirement. In addition, fine filter housing can be provided for through spindle coolant.

Features & Benifits

  • Large dirty tank gives enough time for the chips to settle. It also improves heat dissipation.
  • Single point chip collection.
  • Independently rotating mesh drum with inward and outward flushing nozzle.
  • Multiple drums for larger systems. Drums can be isolated individually.
  • Our unique seal design reduces the seal size.
  • Multi paneled drum for ease of mesh maintenance.
  • Built in PLC Controlled electrical and mechanical safety with Auto conveyor Jamming logic.
  • Skimmers, Weekend agitation, VFD can be added with further enhance the system.
  • Customized design to suit your specific requirement.

CFS Clientele